Zyrnolink Header



Friday 22 February 2013

How to wipe a hard drive in Windows Vista™ or Windows 7

A hard disk drive is the device used to store large amounts of digital information in computers and related equipment like iPods and games consoles such as the Xbox 360 and PS3.
A typical hard disk drive consists of a motor, spindle, platters, read/write heads, actuator and electronics.


PLATTERS
A hard disk has one or more platters - or disks - and each platter usually has a head on each of its sides. In modern drives the platters are made from glass or ceramic. The platters themselves are non-magnetic but have a magnetic coating which holds the magnetic impulses which represent the data. A typical hard drive will have three or four platters and modern varieties can hold 20GB per disk.




READ/WRITE HEAD
The read/write heads float on a cushion of air only nanometers above the surface of the platters. As the read/write heads pass over the spinning platters they magnetize the surface in a pattern which represents the data in digital form. The data is stored digitally as tiny magnetized regions, called bits, on the disk. A magnetic orientation in one direction on the disk could represent a "1", while an orientation in the opposite direction could represent a "0". Data is arranged in sectors along a number of concentric tracks. These tracks are arranged from the inner diameter of the disk to its outer edge. When reading data on a disk, a similar process occurs in reverse.


SPINDLE
The platters are mounted on the spindle which is turned by the drive motor. Most current hard disk drives spin at between 5,400 and 10,000 RPM. Modern hard drives can transfer 80 megabytes of data per second.


HEAD ARM
The triangular-shaped head arm holds the read/write heads and is able to move the heads from the hub to the edge of the drive. There is one hard arm per read/write head and all of them are lined up and mounted to the acuator as a single unit.


VOICE COIL ACTUATOR
The head arm is controlled by an actuator - which has to be incredibly accurate. 30,000 tracks can be stored within one inch of space on a platter. The hard disk's electronics control the movement of the actuator and the rotation of the disk, and perform reads and writes on demand from the disk controller via its interface to the computer.


AIR FILTER
Hard drives are typically air-sealed to enable the heads to float and to avoid contamination from dust. The air inside the hard drive enclosure is in constant motion and passes through the filter to remove any leftover contaminants from the manufacturing process and any particles or chemicals that may have somehow entered the enclosure.


Now that you know what a hard drive is, let us head into the subject matter, which is How To Partition a Hard Drive in Windows 7.

After installing a hard drive , you must partition it (and then format it) before it can be used by Windows 7.
To partition a hard drive in Windows 7 means to divide the hard drive into parts and make those parts available to the operating system. It's also possible for an entire hard drive to have a single partition, which oddly enough is actually the most common way to partition a hard drive.
This might seem very technical but don't worry. Partitioning is a necessary step before you can use a new drive, but Microsoft has made it extremely easy to partition a hard drive in Windows 7.

Difficulty: Easy

Time Required: It usually only takes a few minutes to partition a hard drive in Windows 7.

1. Open Windows 7 Disk Management from the Computer Management utility.

Note: You can also open Disk Management from the Command Prompt in Windows 7 but doing so from Computer Management is probably easier.

2. As Disk Management opens, you should be prompted with an Initialize Disk window advising that "you must initialize a disk before Logical Disk Manager can access it."
Choose MBR if your new hard drive is smaller than 2 terabytes or GPT if it's larger than 2 terabytes. Then click OK.

Note: Don't worry just yet if you don't see this window. We'll know in the next step ifsomething could be wrong with the physical hard drive installation.

3. With Disk Management open, locate the hard drive you want to partition from the graphical drive map on the bottom half of the screen.
If the hard drive is brand new, it will probably be on a dedicated row labeled Disk 1, or some number other than zero, and say Unallocated .
If the space you want to partition is part of physical hard drive that is already partially partitioned, the Unallocated space will be next to that space.

Note: You may need to maximize the Computer Management window to see all the hard drives on the bottom. An unpartitioned drive will not show up in the drive list at the top of the screen.

Important: If you don't see the hard drive you want to partition. Look again, but if you're sure the hard drive you've installed is not there, there may have been an issue when you installed it. Shut down your PC and check to see that the hard drive is installed properly.

4. Once you locate the drive, right-click somewhere on the Unallocated space and choose New Simple Volume... .
The "New Simple Volume Wizard" should appear.

5. Click Next >>.

6. In the Specify Volume Size step, click Next >> to confirm the size of the partition. The size displayed in the Simple volume size in MB: field should equal the size listed as the Maximum disk space in MB:. This means that you're creating a partition that equals the size of the entire hard drive or unpartitioned space.


Note: If you want to create multiple partitions in this unpartitioned space, change the Simple volume size in MB to the size of the partition you'd like to create and repeat this and the following steps to create another, or several more, partitions.

7. The next step, called Assign Drive Letter or Path, does just that, since your new partition will need a drive letter.
Windows 7 automatically chooses the next available drive letter (skipping A and B) so if that drive letter is OK with you, just click Next >>.

Important: It's best to commit to this drive letter. Deciding later to change a drive's letter in Windows 7 can cause problems if programs are installed on the drive.

8. Next, Windows 7 gives you the option to complete a format of the drive immediately after partitioning it. Since this tutorial is focused at partitioning a hard drivep, let's wait to format the drive until we're done creating the partition.
Choose Do not format this volume and then click Next >>.

9. The Completing the New Simple Volume Wizard page displays a quick summary of the partition options you chose.

Check that the settings shown are similar to this:
¤ Volume Type: Simple Volume
¤ Disk selected: Disk 1
¤ Volume size: 2045 MB
¤ Drive letter or path: E.
¤ File system: None
¤ Allocation unit size: Default

Note: The Disk selected, Volume size, and Drive letter or path values will differ depending on your specific setup.


File system: None just means that you've decided not to format the drive at this time.

10. Click Finish to begin Windows 7's partition of the hard drive. Your cursor will turn busy for a few to several seconds. Once your new drive letter (E: in my example) appears in the drive listing at the top of the Disk Management screen, the partition of the hard drive is complete!

11. At this point, Disk Management prompts Windows Explorer to open your new drive.
However, since the new drive is not yet formatted, Windows Explorer gives you the following alert: "You need to format the disk in drive E: before you can use it. Do you want to format it?"
Choose Cancel and follow the directions linked in Step12.

Note: If you're familiar with hard drive formatting, you're welcome to instead click on Format disk and use the directions in Step 12 as a general reference, instead of a specific how-to guide, to performing the format right now.

12. Now that you've partitioned a hard drive, you must format it so Windows 7 can use the drive! Thanks!


INTERESTING ARTICLES
Google adsense blogging rules
How to lock an Operamini
How to create a group chat on 2go
How to configure your operamini or UC Web
How to use your blackberry phone as a moðem
How to prepare African salad or abacha
Get Nigerian business online
How to spot a backlink to your blog
30 characteristics of a masturbator
Comparison between an abridged & unabridged dictionary
How to process a cassava tuber
How to process palm nuts into palm oil
How to format a Symbian phone
Cancerous lipsticks
How to prepare Ogiri-Igbo
Tips on how to quit masturbation
Nokia phone codes
UC Player application download
30 characteristics of a lesbian
2012 best Universities and Colleges in Africa
Miami church brands members with "666" tattoo!
30 characteristics of an occult member
Origin of cultism in Nigerian campuses
Safety precautions in using a mobile device!
How to remod an Operamini
Factors to consider when choosing a female life partner
Factors to consider when choosing a male life partner
How to avoid sexual harassment
Precious Blood of Jesus Christ: The Chaplet & The Devotion
Liverpool FC - The greatest players
Traditional marriage procedures in Igbo land - Nigeria
MC Kings Systems Limited
How to effectively use a social media network

As edited, formatted and published by 'Ucheonye Nzubechi for windows 7 users!

No comments:

Post a Comment